ansible / ansible.builtin / v2.9.0 / module / pn_vrouter_bgp CLI command to add/modify/remove vrouter-bgp | "added in version" 2.9 of ansible.builtin" Authors: Pluribus Networks (@rajaspachipulusu17) preview | supported by communityansible.builtin.pn_vrouter_bgp (v2.9.0) — module
pip
Install with pip install ansible==2.9.0
This module can be used to add Border Gateway Protocol neighbor to a vRouter modify Border Gateway Protocol neighbor to a vRouter and remove Border Gateway Protocol neighbor from a vRouter.
- name: "Add BGP to vRouter" pn_vrouter_bgp: state: 'present' pn_vrouter_name: 'sw01-vrouter' pn_neighbor: '105.104.104.1' pn_remote_as: 65000 pn_bfd: true
- name: "Remove BGP to vRouter" pn_vrouter_bgp: state: 'absent' pn_vrouter_name: 'sw01-vrouter' pn_neighbor: '105.104.104.1'
- name: "Modify BGP to vRouter" pn_vrouter_bgp: state: 'update' pn_vrouter_name: 'sw01-vrouter' pn_neighbor: '105.104.104.1' pn_remote_as: 65000 pn_bfd: false pn_allowas_in: true
state: choices: - present - absent - update default: present description: - vrouter-bgp configuration command. required: false type: str pn_bfd: default: false description: - BFD protocol support for fault detection. required: false type: bool pn_weight: description: - default weight value between 0 and 65535 for the neighbor's routes. required: false pn_neighbor: description: - IP address for BGP neighbor. required: true type: str pn_password: description: - password for MD5 BGP. required: false type: str pn_cliswitch: description: - Target switch to run the CLI on. required: false type: str pn_interface: description: - Interface to reach the neighbor. required: false type: str pn_remote_as: description: - BGP remote AS from 1 to 4294967295. required: false type: str pn_allowas_in: description: - Allow/reject routes with local AS in AS_PATH. required: false type: bool pn_max_prefix: description: - maximum number of prefixes. required: false type: str pn_bfd_multihop: description: - always use BFD multi-hop port for fault detection. required: false type: bool pn_route_map_in: description: - route map in for nbr. required: false type: str pn_vrouter_name: description: - name of service config. required: true type: str pn_ebgp_multihop: description: - value for external BGP from 1 to 255. required: false type: str pn_next_hop_self: description: - BGP next hop is self or not. required: false type: bool pn_route_map_out: description: - route map out for nbr. required: false type: str pn_update_source: description: - IP address of BGP packets required for peering over loopback interface. required: false type: str pn_multi_protocol: choices: - ipv4-unicast - ipv6-unicast description: - Multi-protocol features. required: false pn_prefix_list_in: description: - prefixes used for filtering. required: false type: str pn_send_community: description: - send any community attribute to neighbor. required: false type: bool pn_no_route_map_in: description: - Remove ingress route-map from BGP neighbor. required: false type: str pn_prefix_list_out: description: - prefixes used for filtering outgoing packets. required: false type: str pn_no_route_map_out: description: - Remove egress route-map from BGP neighbor. required: false type: str pn_default_originate: description: - announce default routes to the neighbor or not. required: false type: bool pn_neighbor_holdtime: description: - BGP Holdtime (seconds). required: false type: str pn_override_capability: description: - override capability. required: false type: bool pn_max_prefix_warn_only: description: - warn if the maximum number of prefixes is exceeded. required: false type: bool pn_soft_reconfig_inbound: description: - soft reset to reconfigure inbound traffic. required: false type: bool pn_advertisement_interval: description: - Minimum interval between sending BGP routing updates. required: false type: str pn_connect_retry_interval: description: - BGP Connect retry interval (seconds). required: false type: str pn_route_reflector_client: description: - set as route reflector client. required: false type: bool pn_neighbor_keepalive_interval: description: - BGP Keepalive interval (seconds). required: false type: str
changed: description: indicates whether the CLI caused changes on the target. returned: always type: bool command: description: the CLI command run on the target node. returned: always type: str stderr: description: set of error responses from the vrouter-bgp command. returned: on error type: list stdout: description: set of responses from the vrouter-bgp command. returned: always type: list