ansible / ansible.builtin / v2.9.27 / module / eos_bgp Configure global BGP protocol settings on Arista EOS. | "added in version" 2.8 of ansible.builtin" Authors: Nilashish Chakraborty (@NilashishC) preview | supported by networkansible.builtin.eos_bgp (v2.9.27) — module
pip
Install with pip install ansible==2.9.27
This module provides configuration management of global BGP parameters on Arista EOS devices.
- name: configure global bgp as 64496 eos_bgp: config: bgp_as: 64496 router_id: 192.0.2.1 log_neighbor_changes: True neighbors: - neighbor: 203.0.113.5 remote_as: 64511 timers: keepalive: 300 holdtime: 360 - neighbor: 198.51.100.2 remote_as: 64498 networks: - prefix: 198.51.100.0 route_map: RMAP_1 - prefix: 192.0.2.0 masklen: 23 address_family: - afi: ipv4 safi: unicast redistribute: - protocol: isis route_map: RMAP_1 operation: merge
- name: Configure BGP neighbors eos_bgp: config: bgp_as: 64496 neighbors: - neighbor: 192.0.2.10 remote_as: 64496 description: IBGP_NBR_1 ebgp_multihop: 100 timers: keepalive: 300 holdtime: 360 - neighbor: 192.0.2.15 remote_as: 64496 description: IBGP_NBR_2 ebgp_multihop: 150 operation: merge
- name: Configure root-level networks for BGP eos_bgp: config: bgp_as: 64496 networks: - prefix: 203.0.113.0 masklen: 27 route_map: RMAP_1 - prefix: 203.0.113.32 masklen: 27 route_map: RMAP_2 operation: merge
- name: Configure BGP neighbors under address family mode eos_bgp: config: bgp_as: 64496 address_family: - afi: ipv4 neighbors: - neighbor: 203.0.113.10 activate: yes default_originate: True - neighbor: 192.0.2.15 activate: yes graceful_restart: True operation: merge
- name: remove bgp as 64496 from config eos_bgp: config: bgp_as: 64496 operation: delete
config: description: - Specifies the BGP related configuration. suboptions: address_family: description: - Specifies BGP address family related configurations. suboptions: afi: choices: - ipv4 - ipv6 description: - Type of address family to configure. required: true neighbors: description: - Specifies BGP neighbor related configurations in Address Family configuration mode. suboptions: activate: description: - Enable the Address Family for this Neighbor. type: bool default_originate: description: - Originate default route to this neighbor. type: bool graceful_restart: description: - Enable/disable graceful restart mode for this neighbor. type: bool neighbor: description: - Neighbor router address. required: true weight: description: - Assign weight for routes learnt from this neighbor. - The range is from 0 to 65535 type: int networks: description: - Specify Networks to announce via BGP. - For operation replace, this option is mutually exclusive with root level networks option. suboptions: masklen: description: - Subnet mask length for the Network to announce(e.g, 8, 16, 24, etc.). prefix: description: - Network ID to announce via BGP. required: true route_map: description: - Route map to modify the attributes. redistribute: description: - Specifies the redistribute information from another routing protocol. suboptions: protocol: description: - Specifies the protocol for configuring redistribute information. required: true route_map: description: - Specifies the route map reference. bgp_as: description: - Specifies the BGP Autonomous System (AS) number to configure on the device. required: true type: int log_neighbor_changes: description: - Enable/disable logging neighbor up/down and reset reason. type: bool neighbors: description: - Specifies BGP neighbor related configurations. suboptions: description: description: - Neighbor specific description. ebgp_multihop: description: - Specifies the maximum hop count for EBGP neighbors not on directly connected networks. - The range is from 1 to 255. type: int enabled: description: - Administratively shutdown or enable a neighbor. maximum_prefix: description: - Maximum number of prefixes to accept from this peer. - The range is from 0 to 4294967294. type: int neighbor: description: - Neighbor router address. required: true password: description: - Password to authenticate the BGP peer connection. peer_group: description: - Name of the peer group that the neighbor is a member of. remote_as: description: - Remote AS of the BGP neighbor to configure. required: true type: int remove_private_as: description: - Remove the private AS number from outbound updates. type: bool route_reflector_client: description: - Specify a neighbor as a route reflector client. type: bool timers: description: - Specifies BGP neighbor timer related configurations. suboptions: holdtime: description: - Interval (in seconds) after not receiving a keepalive message that device declares a peer dead. - The range is from 3 to 7200. - Setting this value to 0 will not send keep-alives (hold forever). required: true type: int keepalive: description: - Frequency (in seconds) with which the device sends keepalive messages to its peer. - The range is from 0 to 3600. required: true type: int update_source: description: - Source of the routing updates. networks: description: - Specify Networks to announce via BGP. - For operation replace, this option is mutually exclusive with networks option under address_family. - For operation replace, if the device already has an address family activated, this option is not allowed. suboptions: masklen: description: - Subnet mask length for the Network to announce(e.g, 8, 16, 24, etc.). prefix: description: - Network ID to announce via BGP. required: true route_map: description: - Route map to modify the attributes. redistribute: description: - Specifies the redistribute information from another routing protocol. suboptions: protocol: description: - Specifies the protocol for configuring redistribute information. required: true route_map: description: - Specifies the route map reference. router_id: default: null description: - Configures the BGP routing process router-id value. operation: choices: - merge - replace - override - delete default: merge description: - Specifies the operation to be performed on the BGP process configured on the device. - In case of merge, the input configuration will be merged with the existing BGP configuration on the device. - In case of replace, if there is a diff between the existing configuration and the input configuration, the existing configuration will be replaced by the input configuration for every option that has the diff. - In case of override, all the existing BGP configuration will be removed from the device and replaced with the input configuration. - In case of delete the existing BGP configuration will be removed from the device.
commands: description: The list of configuration mode commands to send to the device returned: always sample: - router bgp 64496 - bgp router-id 192.0.2.1 - bgp log-neighbor-changes - neighbor 203.0.113.5 remote-as 64511 - neighbor 203.0.113.5 timers 300 360 - neighbor 198.51.100.2 remote-as 64498 - network 198.51.100.0 route-map RMAP_1 - network 192.0.2.0 mask 255.255.254.0 - address-family ipv4 - redistribute isis route-map RMAP_1 - exit-address-family type: list