Try SpotterManage Cisco WLC configurations
Authors: James Mighion (@jmighion)
preview | supported by community
Install with ansible-galaxy collection install community.general:==0.1.1
collections:
- name: community.general
version: 0.1.1AireOS does not use a block indent file syntax, so there are no sections or parents. This module provides an implementation for working with AireOS configurations in a deterministic way.
- name: configure configuration
aireos_config:
lines: sysname testDevice
- name: diff the running-config against a provided config
aireos_config:
diff_against: intended
intended: "{{ lookup('file', 'master.cfg') }}"
- name: load new acl into device
aireos_config:
lines:
- acl create testACL
- acl rule protocol testACL 1 any
- acl rule direction testACL 3 in
before: acl delete testACL
- name: configurable backup path
aireos_config:
backup: yes
lines: sysname testDevice
backup_options:
filename: backup.cfg
dir_path: /home/user
src:
description:
- Specifies the source path to the file that contains the configuration or configuration
template to load. The path to the source file can either be the full path on the
Ansible control host or a relative path from the playbook or role root directory. This
argument is mutually exclusive with I(lines).
save:
default: 'no'
description:
- The C(save) argument instructs the module to save the running-config to startup-config. This
operation is performed after any changes are made to the current running config. If
no changes are made, the configuration is still saved to the startup config. This
option will always cause the module to return changed. This argument is mutually
exclusive with I(save_when).
- This option is deprecated as of Ansible 2.7, use C(save_when)
type: bool
after:
description:
- The ordered set of commands to append to the end of the command stack if a change
needs to be made. Just like with I(before) this allows the playbook designer to
append a set of commands to be executed after the command set.
lines:
aliases:
- commands
description:
- The ordered set of commands that should be configured. The commands must be the
exact same commands as found in the device run-config. Be sure to note the configuration
command syntax as some commands are automatically modified by the device config
parser.
match:
choices:
- line
- none
default: line
description:
- Instructs the module on the way to perform the matching of the set of commands against
the current device config. If match is set to I(line), commands are matched line
by line. If match is set to I(none), the module will not attempt to compare the
source configuration with the running configuration on the remote device.
backup:
default: 'no'
description:
- This argument will cause the module to create a full backup of the current C(running-config)
from the remote device before any changes are made. If the C(backup_options) value
is not given, the backup file is written to the C(backup) folder in the playbook
root directory. If the directory does not exist, it is created.
type: bool
before:
description:
- The ordered set of commands to push on to the command stack if a change needs to
be made. This allows the playbook designer the opportunity to perform configuration
commands prior to pushing any changes without affecting how the set of commands
are matched against the system.
provider:
description:
- A dict object containing connection details.
suboptions:
host:
description:
- Specifies the DNS host name or address for connecting to the remote device over
the specified transport.
- The value of host is used as the destination address for the transport.
required: true
type: str
password:
description:
- Specifies the password to use to authenticate the connection to the remote device.
- This value is used to authenticate the SSH session.
- If the value is not specified in the task, the value of environment variable
C(ANSIBLE_NET_PASSWORD) will be used instead.
type: str
port:
default: 22
description:
- Specifies the port to use when building the connection to the remote device.
type: int
ssh_keyfile:
description:
- Specifies the SSH key to use to authenticate the connection to the remote device.
- This value is the path to the key used to authenticate the SSH session.
- If the value is not specified in the task, the value of environment variable
C(ANSIBLE_NET_SSH_KEYFILE) will be used instead.
type: path
timeout:
default: 10
description:
- Specifies the timeout in seconds for communicating with the network device for
either connecting or sending commands.
- If the timeout is exceeded before the operation is completed, the module will
error.
type: int
username:
description:
- Configures the username to use to authenticate the connection to the remote
device.
- This value is used to authenticate the SSH session.
- If the value is not specified in the task, the value of environment variable
C(ANSIBLE_NET_USERNAME) will be used instead.
type: str
save_when:
choices:
- always
- never
- changed
default: never
description:
- When changes are made to the device running-configuration, the changes are not copied
to non-volatile storage by default. Using this argument will change that. If the
argument is set to I(always), then the running-config will always be copied to the
startup-config and the module will always return as changed. If the argument is
set to I(never), the running-config will never be copied to the startup-config. If
the argument is set to I(changed), then the running-config will only be copied to
the startup-config if the task has made a change.
diff_against:
choices:
- intended
- running
description:
- When using the C(ansible-playbook --diff) command line argument the module can generate
diffs against different sources.
- When this option is configured as I(intended), the module will return the diff of
the running-config against the configuration provided in the C(intended_config)
argument.
- When this option is configured as I(running), the module will return the before
and after diff of the running-config with respect to any changes made to the device
configuration.
backup_options:
description:
- This is a dict object containing configurable options related to backup file path.
The value of this option is read only when C(backup) is set to I(yes), if C(backup)
is set to I(no) this option will be silently ignored.
suboptions:
dir_path:
description:
- This option provides the path ending with directory name in which the backup
configuration file will be stored. If the directory does not exist it will be
first created and the filename is either the value of C(filename) or default
filename as described in C(filename) options description. If the path value
is not given in that case a I(backup) directory will be created in the current
working directory and backup configuration will be copied in C(filename) within
I(backup) directory.
type: path
filename:
description:
- The filename to be used to store the backup configuration. If the filename is
not given it will be generated based on the hostname, current time and date
in format defined by <hostname>_config.<current-date>@<current-time>
type: dict
running_config:
aliases:
- config
description:
- The module, by default, will connect to the remote device and retrieve the current
running-config to use as a base for comparing against the contents of source. There
are times when it is not desirable to have the task get the current running-config
for every task in a playbook. The I(running_config) argument allows the implementer
to pass in the configuration to use as the base config for comparison.
intended_config:
description:
- The C(intended_config) provides the master configuration that the node should conform
to and is used to check the final running-config against. This argument will not
modify any settings on the remote device and is strictly used to check the compliance
of the current device's configuration against. When specifying this argument, the
task should also modify the C(diff_against) value and set it to I(intended).
diff_ignore_lines:
description:
- Use this argument to specify one or more lines that should be ignored during the
diff. This is used for lines in the configuration that are automatically updated
by the system. This argument takes a list of regular expressions or exact line
matches.
backup_path: description: The full path to the backup file returned: when backup is yes sample: /playbooks/ansible/backup/aireos_config.2016-07-16@22:28:34 type: str commands: description: The set of commands that will be pushed to the remote device returned: always sample: - hostname foo - vlan 1 - name default type: list updates: description: The set of commands that will be pushed to the remote device returned: always sample: - hostname foo - vlan 1 - name default type: list