community / community.general / 0.1.1 / module / enos_command Run arbitrary commands on Lenovo ENOS devices Authors: Anil Kumar Muraleedharan (@amuraleedhar) preview | supported by communitycommunity.general.enos_command (0.1.1) — module
Install with ansible-galaxy collection install community.general:==0.1.1
collections: - name: community.general version: 0.1.1
Sends arbitrary commands to an ENOS node and returns the results read from the device. The C(enos_command) module includes an argument that will cause the module to wait for a specific condition before returning or timing out if the condition is not met.
# Note: examples below use the following provider dict to handle # transport and authentication to the node. --- vars: cli: host: "{{ inventory_hostname }}" port: 22 username: admin password: admin timeout: 30 --- - name: test contains operator enos_command: commands: - show version - show system memory wait_for: - "result[0] contains 'Lenovo'" - "result[1] contains 'MemFree'" provider: "{{ cli }}" register: result
- assert: that: - "result.changed == false" - "result.stdout is defined"
- name: get output for single command enos_command: commands: ['show version'] provider: "{{ cli }}" register: result
- assert: that: - "result.changed == false" - "result.stdout is defined"
- name: get output for multiple commands enos_command: commands: - show version - show interface information provider: "{{ cli }}" register: result
- assert: that: - "result.changed == false" - "result.stdout is defined" - "result.stdout | length == 2"
match: choices: - any - all default: all description: - The I(match) argument is used in conjunction with the I(wait_for) argument to specify the match policy. Valid values are C(all) or C(any). If the value is set to C(all) then all conditionals in the wait_for must be satisfied. If the value is set to C(any) then only one of the values must be satisfied. retries: default: 10 description: - Specifies the number of retries a command should by tried before it is considered failed. The command is run on the target device every retry and evaluated against the I(wait_for) conditions. commands: description: - List of commands to send to the remote device over the configured provider. The resulting output from the command is returned. If the I(wait_for) argument is provided, the module is not returned until the condition is satisfied or the number of retires as expired. required: true interval: default: 1 description: - Configures the interval in seconds to wait between retries of the command. If the command does not pass the specified conditions, the interval indicates how long to wait before trying the command again. provider: description: - A dict object containing connection details. suboptions: auth_pass: description: - Specifies the password to use if required to enter privileged mode on the remote device. If I(authorize) is false, then this argument does nothing. If the value is not specified in the task, the value of environment variable C(ANSIBLE_NET_AUTH_PASS) will be used instead. type: str authorize: default: false description: - Instructs the module to enter privileged mode on the remote device before sending any commands. If not specified, the device will attempt to execute all commands in non-privileged mode. If the value is not specified in the task, the value of environment variable C(ANSIBLE_NET_AUTHORIZE) will be used instead. type: bool host: description: - Specifies the DNS host name or address for connecting to the remote device over the specified transport. The value of host is used as the destination address for the transport. required: true type: str password: description: - Specifies the password to use to authenticate the connection to the remote device. This value is used to authenticate the SSH session. If the value is not specified in the task, the value of environment variable C(ANSIBLE_NET_PASSWORD) will be used instead. type: str port: default: 22 description: - Specifies the port to use when building the connection to the remote device. type: int ssh_keyfile: description: - Specifies the SSH key to use to authenticate the connection to the remote device. This value is the path to the key used to authenticate the SSH session. If the value is not specified in the task, the value of environment variable C(ANSIBLE_NET_SSH_KEYFILE) will be used instead. type: path timeout: default: 10 description: - Specifies the timeout in seconds for communicating with the network device for either connecting or sending commands. If the timeout is exceeded before the operation is completed, the module will error. type: int username: description: - Configures the username to use to authenticate the connection to the remote device. This value is used to authenticate the SSH session. If the value is not specified in the task, the value of environment variable C(ANSIBLE_NET_USERNAME) will be used instead. type: str type: dict wait_for: description: - List of conditions to evaluate against the output of the command. The task will wait for each condition to be true before moving forward. If the conditional is not true within the configured number of retries, the task fails. See examples. auth_pass: description: - Specifies the password to use if required to enter privileged mode on the remote device. If I(authorize) is false, then this argument does nothing. If the value is not specified in the task, the value of environment variable C(ANSIBLE_NET_AUTH_PASS) will be used instead. authorize: default: false description: - Instructs the module to enter privileged mode on the remote device before sending any commands. If not specified, the device will attempt to execute all commands in non-privileged mode. If the value is not specified in the task, the value of environment variable C(ANSIBLE_NET_AUTHORIZE) will be used instead. type: bool
failed_conditions: description: the conditionals that failed returned: failed sample: - '...' - '...' type: list stdout: description: the set of responses from the commands returned: always sample: - '...' - '...' type: list stdout_lines: description: The value of stdout split into a list returned: always sample: - - '...' - '...' - - '...' - - '...' type: list