netscaler / netscaler.adc / 2.5.1 / module / lsngroup Configuration for LSN group resource. | "added in version" 2.0.0 of netscaler.adc" Authors: Sumanth Lingappa (@sumanth-lingappa) preview | supported by communitynetscaler.adc.lsngroup (2.5.1) — module
Install with ansible-galaxy collection install netscaler.adc:==2.5.1
collections: - name: netscaler.adc version: 2.5.1
Configuration for LSN group resource.
ftp: choices: - ENABLED - DISABLED description: - 'Enable Application Layer Gateway (ALG) for the FTP protocol. For some application-layer protocols, the IP addresses and protocol port numbers are usually communicated in the packet''s payload. When acting as an ALG, the Citrix ADC changes the packet''s payload to ensure that the protocol continues to work over LSN. ' - '' - 'Note: The Citrix ADC also includes ALG for ICMP and TFTP protocols. ALG for the ICMP protocol is enabled by default, and there is no provision to disable it. ALG for the TFTP protocol is disabled by default. ALG is enabled automatically for an LSN group when you bind a UDP LSN application profile, with endpoint-independent-mapping, endpoint-independent filtering, and destination port as 69 (well-known port for TFTP), to the LSN group.' type: str nsip: description: - The ip address of the NetScaler ADC appliance where the nitro API calls will be made. - The port can be specified with the colon (:). E.g. 192.168.1.1:555. required: true type: str pptp: choices: - ENABLED - DISABLED description: - Enable the PPTP Application Layer Gateway. type: str ftpcm: choices: - ENABLED - DISABLED description: - Enable the FTP connection mirroring for specified LSN group. Connection mirroring (CM or connection failover) refers to keeping active an established TCP or UDP connection when a failover occurs. type: str state: choices: - present - absent - unset default: present description: - The state of the resource being configured by the module on the NetScaler ADC node. - When C(present), the resource will be added/updated configured according to the module's parameters. - When C(absent), the resource will be deleted from the NetScaler ADC node. - When C(unset), the resource will be unset on the NetScaler ADC node. type: str sipalg: choices: - ENABLED - DISABLED description: - Enable the SIP ALG. type: str logging: choices: - ENABLED - DISABLED description: - Log mapping entries and sessions created or deleted for this LSN group. The Citrix ADC logs LSN sessions for this LSN group only when both logging and session logging parameters are enabled. - '' - 'The ADC uses its existing syslog and audit log framework to log LSN information. You must enable global level LSN logging by enabling the LSN parameter in the related NSLOG action and SYLOG action entities. When the Logging parameter is enabled, the Citrix ADC generates log messages related to LSN mappings and LSN sessions of this LSN group. The ADC then sends these log messages to servers associated with the NSLOG action and SYSLOG actions entities. ' - '' - 'A log message for an LSN mapping entry consists of the following information:' - '* NSIP address of the Citrix ADC' - '* Time stamp' - '* Entry type (MAPPING or SESSION)' - '* Whether the LSN mapping entry is created or deleted' - '* Subscriber''s IP address, port, and traffic domain ID' - '* NAT IP address and port' - '* Protocol name' - '* Destination IP address, port, and traffic domain ID might be present, depending on the following conditions:' - '** Destination IP address and port are not logged for Endpoint-Independent mapping' - '** Only Destination IP address (and not port) is logged for Address-Dependent mapping' - '** Destination IP address and port are logged for Address-Port-Dependent mapping' type: str nattype: choices: - DYNAMIC - DETERMINISTIC description: - 'Type of NAT IP address and port allocation (from the bound LSN pools) for subscribers:' - '' - 'Available options function as follows:' - '' - '* Deterministic - Allocate a NAT IP address and a block of ports to each subscriber (of the LSN client bound to the LSN group). The Citrix ADC sequentially allocates NAT resources to these subscribers. The Citrix ADC ADC assigns the first block of ports (block size determined by the port block size parameter of the LSN group) on the beginning NAT IP address to the beginning subscriber IP address. The next range of ports is assigned to the next subscriber, and so on, until the NAT address does not have enough ports for the next subscriber. In this case, the first port block on the next NAT address is used for the subscriber, and so on. Because each subscriber now receives a deterministic NAT IP address and a block of ports, a subscriber can be identified without any need for logging. For a connection, a subscriber can be identified based only on the NAT IP address and port, and the destination IP address and port. The maximum number of LSN subscribers allowed, globally, is 1 million. ' - '' - '* Dynamic - Allocate a random NAT IP address and a port from the LSN NAT pool for a subscriber''s connection. If port block allocation is enabled (in LSN pool) and a port block size is specified (in the LSN group), the Citrix ADC allocates a random NAT IP address and a block of ports for a subscriber when it initiates a connection for the first time. The ADC allocates this NAT IP address and a port (from the allocated block of ports) for different connections from this subscriber. If all the ports are allocated (for different subscriber''s connections) from the subscriber''s allocated port block, the ADC allocates a new random port block for the subscriber.' type: str rtspalg: choices: - ENABLED - DISABLED description: - Enable the RTSP ALG. type: str api_path: default: nitro/v1/config description: - Base NITRO API path. - Define only in case of an ADM service proxy call type: str groupname: description: - 'Name for the LSN group. Must begin with an ASCII alphanumeric or underscore (_) character, and must contain only ASCII alphanumeric, underscore, hash (#), period (.), space, colon (:), at (@), equals (=), and hyphen (-) characters. Cannot be changed after the LSN group is created. The following requirement applies only to the Citrix ADC CLI: If the name includes one or more spaces, enclose the name in double or single quotation marks (for example, "lsn group1" or ''lsn group1'').' type: str clientname: description: - Name of the LSN client entity to be associated with the LSN group. You can associate only one LSN client entity with an LSN group.You cannot remove this association or replace with another LSN client entity once the LSN group is created. type: str ip6profile: description: - Name of the LSN ip6 profile to associate with the specified LSN group. An ip6 profile can be associated with a group only during group creation. - '' - By default, no LSN ip6 profile is associated with an LSN group during its creation. Only one ip6profile can be associated with a group. type: str nitro_pass: description: - The password with which to authenticate to the NetScaler ADC node. required: false type: str nitro_user: description: - The username with which to authenticate to the NetScaler ADC node. required: false type: str allocpolicy: choices: - PORTS - IPADDRS description: - NAT IP and PORT block allocation policy for Deterministic NAT. Supported Policies are, - '1: C(PORTS): Port blocks from single NATIP will be allocated to LSN subscribers sequentially. After all blocks are exhausted, port blocks from next NATIP will be allocated and so on.' - '2: C(IPADDRS)(Default): One port block from each NATIP will be allocated and once all the NATIPs are over second port block from each NATIP will be allocated and so on.' - To understand better if we assume port blocks of all NAT IPs as two dimensional array, C(PORTS) policy follows "row major order" and C(IPADDRS) policy follows "column major order" while allocating port blocks. - 'Example:' - 'Client IPs: 2.2.2.1, 2.2.2.2 and 2.2.2.3' - 'NAT IPs and PORT Blocks: ' - 4.4.4.1:PB1, PB2, PB3,., PBn - '4.4.4.2: PB1, PB2, PB3,., PBn' - 'C(PORTS) Policy: ' - 2.2.2.1 => 4.4.4.1:PB1 - 2.2.2.2 => 4.4.4.1:PB2 - 2.2.2.3 => 4.4.4.1:PB3 - 'C(IPADDRS) Policy:' - 2.2.2.1 => 4.4.4.1:PB1 - 2.2.2.2 => 4.4.4.2:PB1 - 2.2.2.3 => 4.4.4.1:PB2 type: str save_config: default: false description: - If C(true) the module will save the configuration on the NetScaler ADC node if it makes any changes. - The module will not save the configuration on the NetScaler ADC node if it made no changes. type: bool sessionsync: choices: - ENABLED - DISABLED description: - In a high availability (HA) deployment, synchronize information of all LSN sessions related to this LSN group with the secondary node. After a failover, established TCP connections and UDP packet flows are kept active and resumed on the secondary node (new primary). - '' - For this setting to work, you must enable the global session synchronization parameter. type: str portblocksize: description: - Size of the NAT port block to be allocated for each subscriber. - '' - To set this parameter for Dynamic NAT, you must enable the port block allocation parameter in the bound LSN pool. For Deterministic NAT, the port block allocation parameter is always enabled, and you cannot disable it. - '' - In Dynamic NAT, the Citrix ADC allocates a random NAT port block, from the available NAT port pool of an NAT IP address, for each subscriber. For a subscriber, if all the ports are allocated from the subscriber's allocated port block, the ADC allocates a new random port block for the subscriber. - '' - The default port block size is 256 for Deterministic NAT, and 0 for Dynamic NAT. type: float snmptraplimit: description: - Maximum number of SNMP Trap messages that can be generated for the LSN group in one minute. type: float nitro_protocol: choices: - http - https default: https description: - Which protocol to use when accessing the nitro API objects. type: str sessionlogging: choices: - ENABLED - DISABLED description: - Log sessions created or deleted for the LSN group. The Citrix ADC logs LSN sessions for this LSN group only when both logging and session logging parameters are enabled. - '' - 'A log message for an LSN session consists of the following information:' - '* NSIP address of the Citrix ADC' - '* Time stamp' - '* Entry type (MAPPING or SESSION)' - '* Whether the LSN session is created or removed' - '* Subscriber''s IP address, port, and traffic domain ID' - '* NAT IP address and port' - '* Protocol name' - '* Destination IP address, port, and traffic domain ID' type: str validate_certs: default: true description: - If C(false), SSL certificates will not be validated. This should only be used on personally controlled sites using self-signed certificates. required: false type: bool nitro_auth_token: description: - The authentication token provided by a login operation. type: str version_added: 2.6.0 version_added_collection: netscaler.adc lsngroup_lsnpool_binding: description: Bindings for lsngroup_lsnpool_binding resource suboptions: binding_members: default: [] description: List of binding members elements: dict type: list mode: choices: - desired - bind - unbind default: desired description: - The mode in which to configure the bindings. - If mode is set to C(desired), the bindings will be added or removed from the target NetScaler ADCs as necessary to match the bindings specified in the state. - If mode is set to C(bind), the specified bindings will be added to the resource. The existing bindings in the target ADCs will not be modified. - If mode is set to C(unbind), the specified bindings will be removed from the resource. The existing bindings in the target ADCs will not be modified. type: str type: dict lsngroup_pcpserver_binding: description: Bindings for lsngroup_pcpserver_binding resource suboptions: binding_members: default: [] description: List of binding members elements: dict type: list mode: choices: - desired - bind - unbind default: desired description: - The mode in which to configure the bindings. - If mode is set to C(desired), the bindings will be added or removed from the target NetScaler ADCs as necessary to match the bindings specified in the state. - If mode is set to C(bind), the specified bindings will be added to the resource. The existing bindings in the target ADCs will not be modified. - If mode is set to C(unbind), the specified bindings will be removed from the resource. The existing bindings in the target ADCs will not be modified. type: str type: dict lsngroup_lsnlogprofile_binding: description: Bindings for lsngroup_lsnlogprofile_binding resource suboptions: binding_members: default: [] description: List of binding members elements: dict type: list mode: choices: - desired - bind - unbind default: desired description: - The mode in which to configure the bindings. - If mode is set to C(desired), the bindings will be added or removed from the target NetScaler ADCs as necessary to match the bindings specified in the state. - If mode is set to C(bind), the specified bindings will be added to the resource. The existing bindings in the target ADCs will not be modified. - If mode is set to C(unbind), the specified bindings will be removed from the resource. The existing bindings in the target ADCs will not be modified. type: str type: dict lsngroup_lsnappsprofile_binding: description: Bindings for lsngroup_lsnappsprofile_binding resource suboptions: binding_members: default: [] description: List of binding members elements: dict type: list mode: choices: - desired - bind - unbind default: desired description: - The mode in which to configure the bindings. - If mode is set to C(desired), the bindings will be added or removed from the target NetScaler ADCs as necessary to match the bindings specified in the state. - If mode is set to C(bind), the specified bindings will be added to the resource. The existing bindings in the target ADCs will not be modified. - If mode is set to C(unbind), the specified bindings will be removed from the resource. The existing bindings in the target ADCs will not be modified. type: str type: dict lsngroup_ipsecalgprofile_binding: description: Bindings for lsngroup_ipsecalgprofile_binding resource suboptions: binding_members: default: [] description: List of binding members elements: dict type: list mode: choices: - desired - bind - unbind default: desired description: - The mode in which to configure the bindings. - If mode is set to C(desired), the bindings will be added or removed from the target NetScaler ADCs as necessary to match the bindings specified in the state. - If mode is set to C(bind), the specified bindings will be added to the resource. The existing bindings in the target ADCs will not be modified. - If mode is set to C(unbind), the specified bindings will be removed from the resource. The existing bindings in the target ADCs will not be modified. type: str type: dict lsngroup_lsnsipalgprofile_binding: description: Bindings for lsngroup_lsnsipalgprofile_binding resource suboptions: binding_members: default: [] description: List of binding members elements: dict type: list mode: choices: - desired - bind - unbind default: desired description: - The mode in which to configure the bindings. - If mode is set to C(desired), the bindings will be added or removed from the target NetScaler ADCs as necessary to match the bindings specified in the state. - If mode is set to C(bind), the specified bindings will be added to the resource. The existing bindings in the target ADCs will not be modified. - If mode is set to C(unbind), the specified bindings will be removed from the resource. The existing bindings in the target ADCs will not be modified. type: str type: dict lsngroup_lsnrtspalgprofile_binding: description: Bindings for lsngroup_lsnrtspalgprofile_binding resource suboptions: binding_members: default: [] description: List of binding members elements: dict type: list mode: choices: - desired - bind - unbind default: desired description: - The mode in which to configure the bindings. - If mode is set to C(desired), the bindings will be added or removed from the target NetScaler ADCs as necessary to match the bindings specified in the state. - If mode is set to C(bind), the specified bindings will be added to the resource. The existing bindings in the target ADCs will not be modified. - If mode is set to C(unbind), the specified bindings will be removed from the resource. The existing bindings in the target ADCs will not be modified. type: str type: dict lsngroup_lsntransportprofile_binding: description: Bindings for lsngroup_lsntransportprofile_binding resource suboptions: binding_members: default: [] description: List of binding members elements: dict type: list mode: choices: - desired - bind - unbind default: desired description: - The mode in which to configure the bindings. - If mode is set to C(desired), the bindings will be added or removed from the target NetScaler ADCs as necessary to match the bindings specified in the state. - If mode is set to C(bind), the specified bindings will be added to the resource. The existing bindings in the target ADCs will not be modified. - If mode is set to C(unbind), the specified bindings will be removed from the resource. The existing bindings in the target ADCs will not be modified. type: str type: dict lsngroup_lsnhttphdrlogprofile_binding: description: Bindings for lsngroup_lsnhttphdrlogprofile_binding resource suboptions: binding_members: default: [] description: List of binding members elements: dict type: list mode: choices: - desired - bind - unbind default: desired description: - The mode in which to configure the bindings. - If mode is set to C(desired), the bindings will be added or removed from the target NetScaler ADCs as necessary to match the bindings specified in the state. - If mode is set to C(bind), the specified bindings will be added to the resource. The existing bindings in the target ADCs will not be modified. - If mode is set to C(unbind), the specified bindings will be removed from the resource. The existing bindings in the target ADCs will not be modified. type: str type: dict
changed: description: Indicates if any change is made by the module returned: always sample: true type: bool diff: description: Dictionary of before and after changes returned: always sample: after: key2: pqr before: key1: xyz prepared: changes done type: dict diff_list: description: List of differences between the actual configured object and the configuration specified in the module returned: when changed sample: - 'Attribute `key1` differs. Desired: (<class ''str''>) XYZ. Existing: (<class ''str''>) PQR' type: list failed: description: Indicates if the module failed or not returned: always sample: false type: bool loglines: description: list of logged messages by the module returned: always sample: - message 1 - message 2 type: list