netscaler / netscaler.adc / 2.5.1 / module / lsntransportprofile Configuration for LSN Transport Profile resource. | "added in version" 2.0.0 of netscaler.adc" Authors: Sumanth Lingappa (@sumanth-lingappa) preview | supported by communitynetscaler.adc.lsntransportprofile (2.5.1) — module
Install with ansible-galaxy collection install netscaler.adc:==2.5.1
collections: - name: netscaler.adc version: 2.5.1
Configuration for LSN Transport Profile resource.
nsip: description: - The ip address of the NetScaler ADC appliance where the nitro API calls will be made. - The port can be specified with the colon (:). E.g. 192.168.1.1:555. required: true type: str state: choices: - present - absent - unset default: present description: - The state of the resource being configured by the module on the NetScaler ADC node. - When C(present), the resource will be added/updated configured according to the module's parameters. - When C(absent), the resource will be deleted from the NetScaler ADC node. - When C(unset), the resource will be unset on the NetScaler ADC node. type: str api_path: default: nitro/v1/config description: - Base NITRO API path. - Define only in case of an ADM service proxy call type: str syncheck: choices: - ENABLED - DISABLED description: - 'Silently drop any non-SYN packets for connections for which there is no LSN-NAT session present on the Citrix ADC. ' - '' - 'If you disable this parameter, the Citrix ADC accepts any non-SYN packets and creates a new LSN session entry for this connection. ' - '' - 'Following are some reasons for the Citrix ADC to receive such packets:' - '' - '* LSN session for a connection existed but the Citrix ADC removed this session because the LSN session was idle for a time that exceeded the configured session timeout.' - '* Such packets can be a part of a DoS attack.' type: str portquota: description: - Maximum number of LSN NAT ports to be used at a time by each subscriber for the specified protocol. For example, each subscriber can be limited to a maximum of 500 TCP NAT ports. When the LSN NAT mappings for a subscriber reach the limit, the Citrix ADC does not allocate additional NAT ports for that subscriber. type: float nitro_pass: description: - The password with which to authenticate to the NetScaler ADC node. required: false type: str nitro_user: description: - The username with which to authenticate to the NetScaler ADC node. required: false type: str save_config: default: false description: - If C(true) the module will save the configuration on the NetScaler ADC node if it makes any changes. - The module will not save the configuration on the NetScaler ADC node if it made no changes. type: bool stuntimeout: description: - STUN protocol timeout type: float sessionquota: description: - 'Maximum number of concurrent LSN sessions allowed for each subscriber for the specified protocol. ' - When the number of LSN sessions reaches the limit for a subscriber, the Citrix ADC does not allow the subscriber to open additional sessions. type: float finrsttimeout: description: - Timeout, in seconds, for a TCP LSN session after a FIN or RST message is received from one of the endpoints. - '' - If a TCP LSN session is idle (after the Citrix ADC receives a FIN or RST message) for a time that exceeds this value, the Citrix ADC ADC removes the session. - '' - Since the LSN feature of the Citrix ADC does not maintain state information of any TCP LSN sessions, this timeout accommodates the transmission of the FIN or RST, and ACK messages from the other endpoint so that both endpoints can properly close the connection. type: float nitro_protocol: choices: - http - https default: https description: - Which protocol to use when accessing the nitro API objects. type: str sessiontimeout: description: - Timeout, in seconds, for an idle LSN session. If an LSN session is idle for a time that exceeds this value, the Citrix ADC removes the session. - '' - This timeout does not apply for a TCP LSN session when a FIN or RST message is received from either of the endpoints. type: float synidletimeout: description: - SYN Idle timeout type: float validate_certs: default: true description: - If C(false), SSL certificates will not be validated. This should only be used on personally controlled sites using self-signed certificates. required: false type: bool nitro_auth_token: description: - The authentication token provided by a login operation. type: str version_added: 2.6.0 version_added_collection: netscaler.adc groupsessionlimit: description: - Maximum number of concurrent LSN sessions(for the specified protocol) allowed for all subscriber of a group to which this profile has bound. This limit will get split across the Citrix ADCs packet engines and rounded down. When the number of LSN sessions reaches the limit for a group in packet engine, the Citrix ADC does not allow the subscriber of that group to open additional sessions through that packet engine. type: float portpreserverange: choices: - ENABLED - DISABLED description: - If a subscriber initiates a connection from a well-known port (0-1023), allocate a NAT port from the well-known port range (0-1023) for this connection. For example, if a subscriber initiates a connection from port 80, the Citrix ADC can allocate port 100 as the NAT port for this connection. - '' - This parameter applies to dynamic NAT without port block allocation. It also applies to Deterministic NAT if the range of ports allocated includes well-known ports. - '' - When all the well-known ports of all the available NAT IP addresses are used in different subscriber's connections (LSN sessions), and a subscriber initiates a connection from a well-known port, the Citrix ADC drops this connection. type: str transportprotocol: choices: - TCP - UDP - ICMP description: - Protocol for which to set the LSN transport profile parameters. type: str portpreserveparity: choices: - ENABLED - DISABLED description: - 'Enable port parity between a subscriber port and its mapped LSN NAT port. For example, if a subscriber initiates a connection from an odd numbered port, the Citrix ADC allocates an odd numbered LSN NAT port for this connection. ' - You must set this parameter for proper functioning of protocols that require the source port to be even or odd numbered, for example, in peer-to-peer applications that use RTP or RTCP protocol. type: str transportprofilename: description: - 'Name for the LSN transport profile. Must begin with an ASCII alphanumeric or underscore (_) character, and must contain only ASCII alphanumeric, underscore, hash (#), period (.), space, colon (:), at (@), equals (=), and hyphen (-) characters. Cannot be changed after the LSN transport profile is created. The following requirement applies only to the Citrix ADC CLI: If the name includes one or more spaces, enclose the name in double or single quotation marks (for example, "lsn transport profile1" or ''lsn transport profile1'').' type: str
changed: description: Indicates if any change is made by the module returned: always sample: true type: bool diff: description: Dictionary of before and after changes returned: always sample: after: key2: pqr before: key1: xyz prepared: changes done type: dict diff_list: description: List of differences between the actual configured object and the configuration specified in the module returned: when changed sample: - 'Attribute `key1` differs. Desired: (<class ''str''>) XYZ. Existing: (<class ''str''>) PQR' type: list failed: description: Indicates if the module failed or not returned: always sample: false type: bool loglines: description: list of logged messages by the module returned: always sample: - message 1 - message 2 type: list